Alamo DSEB-D16 User Manual Page 51
- Page / 119
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
A-Boom (JD 6615 / 7615 Asy Instruction Manual) 07/03
© 2003 Alamo Group Inc.
Section 4 - 22
Frame Rail Installation
Remove High Frame for Welding.:
1. Remove Frame Rails. It is best to remove the
Frame Rails to weld them. Frame Rails will need to
be welded in five places. Note: The RH Frame Rail
and the LH Frame Rail will have the same Welding
done. For Illustration we are showing the RH Frame
Rail, but the LH will have to be done also.
2. Weld Front Mount Plate. Weld down each side
between Bolt Holes. Do not Weld to where the
Weld will interfere with the Hex Head of Bolts when
they are installed. Also weld across the Front of the
Mounting Pad. (See Figure 51, 55 & 56)
3. Weld Front Angle Mount. Weld the Front Angle
Mount to the Frame Rail on the Sides running
parallel to the Frame Rail, Not across Frame Rail
(See Figure 52 & 58). Weld the Rear Angle Mount
to Frame rail the same as the front (See Figure
53).
4. Bar Mounting Strap. Weld these all the way
around, first check your measurements for place-
ment. The Bar Mounting Straps are cut and must
be placed to where they will line up with the ones
that you welded to the High frame mounting tubes
earlier. (See Figure 53)
5. Frame Rail Stiffener Weldment. Weld the
Frame stiffener to Frame rail on both sides. (See
Figure 24). Touch up or re-paint frame compo-
nents after welding is completed. There are
other components that need to be installed
before you reinstall frame.
2
Figure 51
Do Not Weld next to Bolt Holes, it
will interfere Hex Heads of Bolts
3
Figure 52
Weld along sides of Angle Mount
and frame rail on both sides (this
applies to"A" & "B")
5
Figure 54
4
Figure 53
3
- ALAMO INDUSTRIAL 1
- Assembly Instruction Manual 1
- John Deere 6615 and 7615 1
- TO THE OWNER/OPERATOR/DEALER 2
- INTRODUCTION 3
- INDEX - ASSEMBLY INSTRUCTION 4
- Safety Section 1-1 7
- (SG-2) 9
- © 2003 Alamo Group Inc 10
- © 2003Alamo Group Inc 11
- Section 1 13
- Assembly 14
- Saftey Equipment: 15
- Frame and Boom: 15
- Hydraulic System: 15
- Rotary Mower Head: 15
- Flail Mower Head: 16
- Post-Operation Inspection: 16
- For Check List 17
- Section 2 18
- Rear Wheel Counter Weight 19
- Figure 1 19
- Figure 3 20
- Figure 2 20
- Section 3 22
- Figure 10 26
- Figure 11 26
- Figure 12 26
- Figure 14 27
- Figure 15 27
- Figure 13 27
- Figure 16 27
- Figure 17 28
- Figure 19 28
- Figure 18 28
- Section 4 30
- Frame Rail Set Up 31
- Frame Rail Installation 32
- Frame Stiiffener Kit 33
- High Frame Installation 35
- Rear Axle 39
- Floor Jack and 39
- Frame Rail 39
- Figure 20 40
- Figure 21 41
- Figure 23 41
- Figure 24 41
- Figure 22 41
- Figure 25 42
- Figure 26 42
- Figure 28 42
- Figure 27 42
- Figure 29 43
- Figure 30 43
- Figure 32 44
- Figure 31 44
- Figure 33 45
- Figure 34 45
- Figure 35 46
- Figure 37 46
- Figure 36 46
- Figure 38 46
- Figure 39 47
- Figure 40 48
- Figure 41 48
- Figure 44 49
- Figure 42 49
- Figure 43 49
- Figure 45 49
- Figure 51 51
- Figure 52 51
- Figure 54 51
- Figure 53 51
- Figure 56 52
- Figure 55 52
- Figure 57 52
- Figure 58 52
- Section 5 54
- Frame Rail Installation 4 WD 58
- Section 6 62
- Hyd. Tank - CWT Installation 63
- Decal Installation 64
- Section 7 66
- Boom Installation 67
- Front of Tank & 69
- Front of Tractor 69
- Hose Installation 70
- Section 8 72
- Common Problems: 75
- System Schematic 77
- MECHANICAL VALVE MODELS 79
- Section 9 84
- Optional Joystick Mounting 85
- Option Joystick Mounting 86
- FIGURE 5 86
- FIGURE 6 87
- FIGURE 7 87
- FIGURE 8 87
- FIGURE 9 88
- Installing Wiring 89
- Harness to Joystick: 89
- (Continued) 89
- FIGURE 16 90
- FIGURE 17 90
- FIGURE 18 90
- FIGURE 19 91
- FIGURE 20 91
- FIGURE 21 91
- FIGURE 22 91
- FIGURE 23 92
- FIGURE 24 92
- FIGURE 26 92
- FIGURE 25 92
- FIGURE 27 93
- FIGURE 28 93
- FIGURE 29 93
- Actual Pin Location 94
- IS SHOWN in this 94
- Illustration 94
- FIGURE 32 96
- FIGURE 33 96
- Section 10 98
- Figure 4 100
- Figure 5 101
- Figure 6 102
- Figure 7 103
- Figure 8 103
- Figure 9 103
- Section 11 104
- Fill Hydraulic Tank 105
- FIGURE 1 105
- FIGURE 3 FIGURE 4 105
- FIGURE 2 105
- Section 12 108
- Start-up Instructions: 109
- Post-Assembly Check List: 110
- Section 13 112
- FIGURE 3 113
- FIGURE 4 113
- Boom Swing Stop Installation 115
- FIGURE 10 115
- FIGURE 11 115
- FIGURE 12 115
- FIGURE 13 115
Related products and manuals for Tractor Alamo DSEB-D16
Tractor Alamo EAGLE 10/15 User Manual
(180 pages)
(180 pages)
Tractor Alamo SX15 User Manual
(160 pages)
(160 pages)
Tractor Alamo RHINO TX235 User Manual
(150 pages)
(150 pages)
Tractor Alamo Brahma 02968822P User Manual
(64 pages)
(64 pages)
© 2020, manymanuals.com. All rights reserved. | 0.389 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals