Alamo DSEB-D16 User Manual Page 109
- Page / 119
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
A-Boom (JD 6615 / 7615 Asy Instruction Manual) 07/03
© 2003 Alamo Group Inc.
Section 12 - 2
Start-up Instructions:
1. Read all safety instructions. Decals on the A-Boom warn you of particular and multiple
Hazards. Many decals are attached close to part of the A-Boom where there is apossible
hazard. Read and make sure you understand the safety messages before you operate the A-
Boom. Keep all decals clean and readable. Replace lost or damaged decals.
2. Before operating, read all the safety and operating instructions in the Operator's Manuals for
both the tractor and mower.
3. When the hydraulic tank has been filled, The Pump Suction Hose filled with Hydraulic Oil and
the mower unit (Head) properly assembled, the unit should be started up. NOTE: Make sure
that no materials, tools, or jacks have been left under the mower head. Make sure the front
and rear of the mower are properly guarded to prevent any foreign objects from being thrown
by the mower. All other workers should be kept a safe distance from the unit before the mower
is started.
4. Start the tractor and idle at a slow engine speed until oil is being pumped. Check for any leaks,
this is easiest with an assistant watching for leaks. Do not run if Oil is leaking.
5. Bleed the air out of all hydraulic cylinders one at a time by extending them to their full length. DO
NOT SWING THE BOOM till last and you have gone to the Rest Stop and Support Section for
instructions.
6. Engage the Cutter Control Valve at low engine rpm and run the mower slowly for a short
period until all air is removed from the hoses. Keep all persons WELL CLEAR of mower since
Blades can THROW OBJECTS with great velocity for a considerable distance! KEEP CLEAR!
7. Run the mower at a low tractor engine speed until the mower Hydraulic Sytstem gets the Air
out off it. Operate at an engine speed that keeps the filter restriction gauge reading in the
"Green Zone". With the hydraulic warm, bring the tractor speed up to normal operating speed.
If the filter gauge reads in the red zone, stop the unit, release all hydraulic oil pressure, and
Check the filter element in the tank mounted filter or any Hose that may be kinked. Restart the
tractor and mower unit and again check the filter gauge (oil must still be hot).
8. If the filter gauge reads in the red when first started and does not drop as oil warmss, then
something is wrong, contaminants have been introduced into the hydraulic system or some
thing connected wrong. You may need to repeat previous steps again until the gauge reads in
the green.
9. Check the fluid level in the Hydraulic Tank and add oil if required. As the air has been forced
out of the Cylinders and Hoses, it goes into the Hydraulic Tank and reduces the oil level. The
Hydraulic Oil must be at least at the level of the Sight Gauge on the side of the Tank.
10. Basic trouble shooting guide for first start up.
A. Electrical solenoid valve does not work - check wiring, possible faulty switch, possible
faulty solenoid.
B. Pump is making noise - check for obstruction in suction hose and tank suction assembly,
check alignment of pump driveshaft.
C. Cylinders will not raise - hoses from cylinder incorrectly connected to valve bank, pump
not suppling oil.
D. Cylinder rises slowly - hoses from cylinder incorrectly connected to valve bank, work port
reliefs on valve bank set too low - replace as required.
E. Filter reads in red - viscosity of oil too high - wait until oil heats up before checking filter
gauge. If gauge reads in red even after unit is hot, then the filter must be replaced.
- ALAMO INDUSTRIAL 1
- Assembly Instruction Manual 1
- John Deere 6615 and 7615 1
- TO THE OWNER/OPERATOR/DEALER 2
- INTRODUCTION 3
- INDEX - ASSEMBLY INSTRUCTION 4
- Safety Section 1-1 7
- (SG-2) 9
- © 2003 Alamo Group Inc 10
- © 2003Alamo Group Inc 11
- Section 1 13
- Assembly 14
- Saftey Equipment: 15
- Frame and Boom: 15
- Hydraulic System: 15
- Rotary Mower Head: 15
- Flail Mower Head: 16
- Post-Operation Inspection: 16
- For Check List 17
- Section 2 18
- Rear Wheel Counter Weight 19
- Figure 1 19
- Figure 3 20
- Figure 2 20
- Section 3 22
- Figure 10 26
- Figure 11 26
- Figure 12 26
- Figure 14 27
- Figure 15 27
- Figure 13 27
- Figure 16 27
- Figure 17 28
- Figure 19 28
- Figure 18 28
- Section 4 30
- Frame Rail Set Up 31
- Frame Rail Installation 32
- Frame Stiiffener Kit 33
- High Frame Installation 35
- Rear Axle 39
- Floor Jack and 39
- Frame Rail 39
- Figure 20 40
- Figure 21 41
- Figure 23 41
- Figure 24 41
- Figure 22 41
- Figure 25 42
- Figure 26 42
- Figure 28 42
- Figure 27 42
- Figure 29 43
- Figure 30 43
- Figure 32 44
- Figure 31 44
- Figure 33 45
- Figure 34 45
- Figure 35 46
- Figure 37 46
- Figure 36 46
- Figure 38 46
- Figure 39 47
- Figure 40 48
- Figure 41 48
- Figure 44 49
- Figure 42 49
- Figure 43 49
- Figure 45 49
- Figure 51 51
- Figure 52 51
- Figure 54 51
- Figure 53 51
- Figure 56 52
- Figure 55 52
- Figure 57 52
- Figure 58 52
- Section 5 54
- Frame Rail Installation 4 WD 58
- Section 6 62
- Hyd. Tank - CWT Installation 63
- Decal Installation 64
- Section 7 66
- Boom Installation 67
- Front of Tank & 69
- Front of Tractor 69
- Hose Installation 70
- Section 8 72
- Common Problems: 75
- System Schematic 77
- MECHANICAL VALVE MODELS 79
- Section 9 84
- Optional Joystick Mounting 85
- Option Joystick Mounting 86
- FIGURE 5 86
- FIGURE 6 87
- FIGURE 7 87
- FIGURE 8 87
- FIGURE 9 88
- Installing Wiring 89
- Harness to Joystick: 89
- (Continued) 89
- FIGURE 16 90
- FIGURE 17 90
- FIGURE 18 90
- FIGURE 19 91
- FIGURE 20 91
- FIGURE 21 91
- FIGURE 22 91
- FIGURE 23 92
- FIGURE 24 92
- FIGURE 26 92
- FIGURE 25 92
- FIGURE 27 93
- FIGURE 28 93
- FIGURE 29 93
- Actual Pin Location 94
- IS SHOWN in this 94
- Illustration 94
- FIGURE 32 96
- FIGURE 33 96
- Section 10 98
- Figure 4 100
- Figure 5 101
- Figure 6 102
- Figure 7 103
- Figure 8 103
- Figure 9 103
- Section 11 104
- Fill Hydraulic Tank 105
- FIGURE 1 105
- FIGURE 3 FIGURE 4 105
- FIGURE 2 105
- Section 12 108
- Start-up Instructions: 109
- Post-Assembly Check List: 110
- Section 13 112
- FIGURE 3 113
- FIGURE 4 113
- Boom Swing Stop Installation 115
- FIGURE 10 115
- FIGURE 11 115
- FIGURE 12 115
- FIGURE 13 115
Related products and manuals for Tractor Alamo DSEB-D16
Tractor Alamo EAGLE 10/15 User Manual
(180 pages)
(180 pages)
Tractor Alamo SX15 User Manual
(160 pages)
(160 pages)
Tractor Alamo RHINO TX235 User Manual
(150 pages)
(150 pages)
Tractor Alamo Brahma 02968822P User Manual
(64 pages)
(64 pages)
© 2020, manymanuals.com. All rights reserved. | 0.852 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals