Alamo DSEB-D16 User Manual Page 26
- Page / 119
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
© 2003 Alamo Group Inc.
Section 3 - 5
A-Boom (JD 6615 / 7615 Asy Instruction Manual) 07/03
Pump / Drive Assembly Instructions
4. Loosen Splined Clamp Yoke. Insert a bar
through the Yoke to hold Driveshaft up and to help
loosen the Bolts in the clamp Yoke (See Figure 10).
This can be loosened with a hand Wrench or a
Socket whichever is easier for you (See Figure 10).
Some times it is easier to test fit the Tube End of
Driveshaft to the Pump while the Pump is on the
bench.
Installing Pump:
1. Install Pump into Splined Clamp Yoke. Slide
the Pump Splined Shaft into the Spline Clamp Yoke
(See Figure 11). Leave the Bar stuck in through the
Yoke as shown, this helps to stabilize the Yoke as
you slide Shaft into the Yoke. Once Pump is slid into
the Splined Yoke, keep the Pump supported; DO
NOT let the Pump hang on the Yoke unsupported.
2. Pump / Driveshaft Yoke Gap Adjustment.
After sliding Pump Shaft into Splined Clamp Yoke,
the Pump and Yoke must be slid apart far enough to
allow for a 1/16" to 1/8" Gap between them. The Yoke
edge cannot touch the Pump Housing; it will damage
the Housing and the Yoke if it does. This is a very
critical adjustment (See Figure 12).
3. Tighten Clamp Yoke. After Gap between
Yoke and Pump has been adjusted tighten the Bolts
& Nuts on the Clamp Yoke (See Figure 12 & 13).
Check Pump to Yoke Gap once more. Keep Pump
Supported do not let it hang on Yoke.
Figure 10
Bar to Hold
Driveshaft
Loosen
Clamp
Yoke Bolt
Figure 9
Bar to Hold
Drive Shaft
Driveshaft, Spline
Clamp Yoke End
Figure 11
Bar to Hold
Driveshaft
Align Splines of
Pump Shaft w/
Splines of Yoke
Figure 12
Pump
Assembly
Splined
Clamp
Yoke
1/16" to 1/8" Gap
between Pump &
Yoke (must)
Installing Pump Mount Plate & Tube End of Driveshaft: (continued)
- ALAMO INDUSTRIAL 1
- Assembly Instruction Manual 1
- John Deere 6615 and 7615 1
- TO THE OWNER/OPERATOR/DEALER 2
- INTRODUCTION 3
- INDEX - ASSEMBLY INSTRUCTION 4
- Safety Section 1-1 7
- (SG-2) 9
- © 2003 Alamo Group Inc 10
- © 2003Alamo Group Inc 11
- Section 1 13
- Assembly 14
- Saftey Equipment: 15
- Frame and Boom: 15
- Hydraulic System: 15
- Rotary Mower Head: 15
- Flail Mower Head: 16
- Post-Operation Inspection: 16
- For Check List 17
- Section 2 18
- Rear Wheel Counter Weight 19
- Figure 1 19
- Figure 3 20
- Figure 2 20
- Section 3 22
- Figure 10 26
- Figure 11 26
- Figure 12 26
- Figure 14 27
- Figure 15 27
- Figure 13 27
- Figure 16 27
- Figure 17 28
- Figure 19 28
- Figure 18 28
- Section 4 30
- Frame Rail Set Up 31
- Frame Rail Installation 32
- Frame Stiiffener Kit 33
- High Frame Installation 35
- Rear Axle 39
- Floor Jack and 39
- Frame Rail 39
- Figure 20 40
- Figure 21 41
- Figure 23 41
- Figure 24 41
- Figure 22 41
- Figure 25 42
- Figure 26 42
- Figure 28 42
- Figure 27 42
- Figure 29 43
- Figure 30 43
- Figure 32 44
- Figure 31 44
- Figure 33 45
- Figure 34 45
- Figure 35 46
- Figure 37 46
- Figure 36 46
- Figure 38 46
- Figure 39 47
- Figure 40 48
- Figure 41 48
- Figure 44 49
- Figure 42 49
- Figure 43 49
- Figure 45 49
- Figure 51 51
- Figure 52 51
- Figure 54 51
- Figure 53 51
- Figure 56 52
- Figure 55 52
- Figure 57 52
- Figure 58 52
- Section 5 54
- Frame Rail Installation 4 WD 58
- Section 6 62
- Hyd. Tank - CWT Installation 63
- Decal Installation 64
- Section 7 66
- Boom Installation 67
- Front of Tank & 69
- Front of Tractor 69
- Hose Installation 70
- Section 8 72
- Common Problems: 75
- System Schematic 77
- MECHANICAL VALVE MODELS 79
- Section 9 84
- Optional Joystick Mounting 85
- Option Joystick Mounting 86
- FIGURE 5 86
- FIGURE 6 87
- FIGURE 7 87
- FIGURE 8 87
- FIGURE 9 88
- Installing Wiring 89
- Harness to Joystick: 89
- (Continued) 89
- FIGURE 16 90
- FIGURE 17 90
- FIGURE 18 90
- FIGURE 19 91
- FIGURE 20 91
- FIGURE 21 91
- FIGURE 22 91
- FIGURE 23 92
- FIGURE 24 92
- FIGURE 26 92
- FIGURE 25 92
- FIGURE 27 93
- FIGURE 28 93
- FIGURE 29 93
- Actual Pin Location 94
- IS SHOWN in this 94
- Illustration 94
- FIGURE 32 96
- FIGURE 33 96
- Section 10 98
- Figure 4 100
- Figure 5 101
- Figure 6 102
- Figure 7 103
- Figure 8 103
- Figure 9 103
- Section 11 104
- Fill Hydraulic Tank 105
- FIGURE 1 105
- FIGURE 3 FIGURE 4 105
- FIGURE 2 105
- Section 12 108
- Start-up Instructions: 109
- Post-Assembly Check List: 110
- Section 13 112
- FIGURE 3 113
- FIGURE 4 113
- Boom Swing Stop Installation 115
- FIGURE 10 115
- FIGURE 11 115
- FIGURE 12 115
- FIGURE 13 115
Related products and manuals for Tractor Alamo DSEB-D16
Tractor Alamo EAGLE 10/15 User Manual
(180 pages)
(180 pages)
Tractor Alamo SX15 User Manual
(160 pages)
(160 pages)
Tractor Alamo RHINO TX235 User Manual
(150 pages)
(150 pages)
Tractor Alamo Brahma 02968822P User Manual
(64 pages)
(64 pages)
© 2020, manymanuals.com. All rights reserved. | 0.259 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals